Sundial Creation

A sundial is an easy and simple way to tell time just by using the sun. The sun as been an accurate timekeeping device for centuries and you can create your own. The earliest sundial was used was named "shadow clocks" and was used as early as 1500BC. Most recordings of sundial usage was done by the early Egyptians and Babylonians and they used forms of astrology to keep time. Sundials were used long before analog and are quite impressive to see the time changes as the sun moves across the sky. Here's how it's made...

What you'll need:

1. A straight piece of metal or wood. (We used a short length of rebar)

2. 12 large stones, 12 medium stones, and 12 small stones

3. String or measuring tape

4. A watch

What to do:

You need to find a clean, flat surface of ground that is sunny and clear off the area of any large debris, sticks, twigs, leaves, grass, and/or other items. Make sure the area is flat, and if there's slopes or grooves, rake the area clean and get it as level as you can.

Next, Hammer your piece of metal, or wood into the ground where you want the middle of the sundial to be. We used a rake and cleared the area and then raked in a circle for aesthetics. 

Next, tie your string to your middle piece and stretch out. Your sundial can be as big, or as small as you like. We wanted a bigger one, so we adjusted accordingly. Take your string around your middle stick and go around in a circle. As you go mark areas of your sundial that you need to either make bigger or smaller. You want to make sure your circle is even all the way around.

Once you've made your circle even all the way around, next you want to mark your time for that moment. Example: If you're doing this project at 1:00 p.m., the sun should cast a shadow on your middle piece onto a spot on your sundial. Place a large stone at that mark on the outer edge of your sundial. Then, set your timer and head back out to place your stone for 2:00 p.m. and so on. For the morning times, start at 7:00 a.m. and place a large stone for 7:00 a.m. Go back every hour and place large stones on the appropriate times. By the end of 24 hours you should have enough large stones in place to finish your dial. Estimate where the remaining large stones should be. 

Next, place medium stones between the large stones on your dial. These medium stones will be the marks for the half hour. Example: Place a medium stone between the 1:00 p.m. and the 2:00 p.m. larger stones. 

Finally, place the smaller stones inside the outer ring of stones between each medium and large stone. These will be the marks for the 15 minute time intervals. Example: Place a small stone between 1:00 p.m. and 1:30 p.m., as well as between 1:30 p.m. and 2:00 p.m. 

Continue around your entire dial and you're done!

Keep in mind that the shadows that are casts against your middle object will change throughout the year and from season to season. In the summer, when we did this project, the shadows were shorter. But, in the winter, the shadows cast will be longer. Although the days in winter are seems shorter, the shadows from the sun will be longer shadows. You can learn more about the shadows and sundials here.

A.M. stands for "ante meridiem," which means before noon and the P.M. stands for "post meridiem," meaning after noon. All time equivalent is before the noon hour or after the noon hour.

Side Note: Be sure to wear gloves while clearing a space for your sundial. We are all nursing a few blisters from our hard work. It was worth the effort, though, because our sundial is large and in a space where we can look at it often.

And, thanks to this guy for helping us lay everything out.

Homemade Fingerprint Powder

Have you ever wanted to be a forensic specialist and investigate a crime? As unfortunately as the world is, we can't get away from crime and heinous actions of others. With these crimes, forensic and crime scene investigators go to these crime scenes with a tool to find out if the criminal left any fingerprints that could link them back to their evil deeds. This tool is fingerprint powder. Although, the process to create fingerprint powder at home is a bit different than what is actually used, it still serves the same purpose in identifying fingerprints on objects. We recreated our own fingerprint powder and experimented on glasses to lift fingerprints off the surface. This simple fingerprint powder can be recreated at your own home and you can play around to see what surfaces you can lift fingerprints from and identify whose print is whose. Be careful, though, this powder will stain surfaces. Glass is a preferred surface.

• Materials Needed:
• 1. Cornstarch
• 2. Measuring Cup
• 3. Candle
• 4. Porcelain dish or metal spoon
• 5. Knife
• 6. Small bowl
• 7. Small paint brush
• 8. Small funnel
• 9. Small jar with lid
• 10. Patience

Start by using a candle, bowl, and a metal spoon. Place the candle in the bowl and light. Using the flame of the candle (in a very well ventilated area, preferable outside), place the spoon over the flame and allow it to burn the back of the spoon. After a short time we will create soot on the back of the spoon. Scrap the soot off each time it's created. We will need about a tablespoon to 1/4 a cup of soot, so this takes some time. We did our collection over a period of several days. 

Depending on how much soot you have created you need to mix the same amount of corn starch with the soot powder. So, say you have a tablespoon of soot, mix that soot with a tablespoon of corn starch. 

Next, have friends or family to touch their forehead and then touch a glass surface. We used drinking glasses here, but you can also touch countertops, sliding glass doors, windows, and even plastic bottles, or soda cans. Just remember, whatever you use for your surface, make sure it's easy to clean up afterwards.

Once they place their fingers on the surface you can see the fingerprints, but only faintly. 

Next step is to use your newly created fingerprint powder and using a soft paint brush, lightly brush the powder over the fingerprint. Be careful not to press too hard, or you will disturb the oils in the print. Once you lightly lay a layer over the print, tap the glass to remove the excess powder.

Next step is to use clear packing tape, of course any clear, wide tape would work, we just happened to have clear packing tape on hand. You want to use the tape and place it directly over your fingerprints. Be careful not to press down too hard as you could damage the print, but a light rubbing over the top of each one is going to help with the lifting process of the print with the fingerprint powder.

Next step is to lift the prints and place them onto white paper. We used small post-it notes to adhere our prints, but computer paper would work, too. Place your tape down on the paper and press lightly. Here you can view your prints without worrying about messing them up any further. If you did several people's prints, it's interesting to see the difference in each person's print. Make note of how different they are, and if these prints were to be gathered for criminal reasons, how would each person be able to be caught, or eliminated? 

Be sure to save the rest of your fingerprint powder to use again in the future. We stored ours in a small corked glass jar along with the funnel and the soft paint brush. You can store yours in anything that seals and is able to be put away without spilling. Remember, this fingerprint powder has soot in it and will stain most surfaces. 

If you create this project we'd love to see it. Tag #rainvalleyredsnails on Instagram or Twitter, so we can see your fingerprint creations.